After configuring FabricPath， the following appears in the syslog：
%STP-2-L2GW_BACKBONE_BLOCK： L2 Gateway Backbone port inconsistency blocking port port-channel100 on VLAN0010.
What is the cause of this message？ （）
A. STP must be disabled； message indicates that STP is enabled.
B. STP is misconfigured； root guard must be disabled.
C. An inferior BPDU is received on a Cisco FabricPath edge port.
D. A superior BPDU is received on a Cisco FabricPath edge port.
您可能感興趣的試卷
你可能感興趣的試題
A. short-text-destination
B. prerecorded audio alerts
C. CiscoTAC-1
D. dial911
E. full-text-destination
A. FabricPath switch ID must be configured under the vPC domain.
B. Virtual switch ID of vPC+ must be configured under FabricPath domain.
C. On Cisco Nexus 7000 Series Switch， F1 interfaces must be used as the vPC+ peer links.
D. The vPC+ peer link must be configured as a Cisco FabricPath core port （switchport mode fabricpath）.
E. FabricPath subswitch ID must be configured under the vPC domain.
A. encryption—scrambles the packet contents to prevent them from being seen by unauthorized sources
B. password—a password （community string） sent in clear text between a manager and agent for added protection
C. authentication—determines that the message is from a valid source
D. message integrity—ensures that a packet has not been tampered with while it was in transit
E. user—to determine if user authentication is used instead of community strings
A. Join interface is a Layer 3 entity， and with the Cisco NX-OS release 6.0， it can only be defined as a physical interface， physical subinterface， Layer 3 port channel， or Layer 3 port channel subinterface.
B. A single join interface can be defined and associated with a given OTV overlay.
C. Multiple overlays can also share the same join interface.
D. Join interface can be a loopback interface.
E. The join interface is a Layer 3 entity that can be defined as a physical interface but not as a logical one.
The network administrator is seeing N7K-1 having issues with VLAN 11， and interface VLAN 11 is resetting， causing frequent HSRP state changes. Which two actions would reduce HSRP state changes？ （）
A..On N7K-1，configure the HSRP extended hold timer to 180， extending the HSRP hello message hold time.
B..On N7K-2，configure the HSRP extended hold timer to 180， extending the HSRP hello message hold time.
C..On N7K-1，configure the pre-empt delay minimum to 180 in order to delay N7K-1 from taking over as the HSRP active router.
D..On N7K-2，configure the pre-empt delay minimum to 180 in order to delay N7K-2 from taking over as the HSRP active router.
E..On N7K-2，increase the HSRP priority to 150.
F. On N7K-2，decrease the HSRP priority to 50.
最新試題
What would be the cause for the following fault in UCS Manager？（） "ether VIF x / xxx down， reason： ENM source pinning failed"
Which statement is true about "full state backup" in a Cisco Unified Computing System？（）
In a Cisco Unified Computing System， where are SAN port channels connected to？（）
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）
What is the use of an "all configuration" backup in Cisco UCS？（）
An administrator creates a vNIC and assigns it to Fabric A with the fabric failover feature enabled. Which statement is true？（）
What is the appliance port used to connect to in a Cisco Unified Computing System？（）
When testing ICMP access to a functional load-balancing ACE VIP， it fails. What is the reason of this problem？ （）
Refer to the exhibit. According to the equipment tab in Cisco UCS Manager， which is true？（）
Which two statements about end-host mode in SAN connectivity in a Cisco UCS environment are true？ （）