Nexus# conf t
Enter configuration commands， one per line. End with CNTL/Z.
Nexus（config）# interface Loopback10
% Permission denied Nexus（config）# ？
no Negate a command or set its defaults
username Configure user information.
end Go to exec mode
exit Exit from command interpreter
What is the reason why this user is not able to enter configuration commands？（）
A. The user did not enter enable prior to going into configuration mode.
B. The software license installed on Nexus is Layer 2 only， which does not allow the creation of Layer 3 interfaces.
C. The user RBAC role is set to network-operator.
D. The user failed authentication and user access defaulted to read-only mode.
E. The AAA server is currently not responding.
您可能感興趣的試卷
你可能感興趣的試題
A. Cisco DCNM-LAN server users are local to the Cisco DCNM-LAN server. Creating， changing， and removing Cisco DCNM-LAN server users has no effect on user accounts on managed devices.
B. A Cisco DCNM-LAN server user that has Administrator privileges can push out changes to managed devices even if the Cisco NX-OS role that is used on the discovered device has the network operator role.
C. Cisco DCNM-LAN user roles restrict the ability of users to make changes to Cisco DCNM-LAN server settings. Cisco NX-OS user roles enforce read/write privileges on the discovered devices.
D. Cisco DCNM-LAN allows you to configure unique credentials for each discovered device or use default credentials when you do not configure unique credentials for a device.
E. Cisco DCNM-LAN can use AAA servers to authenticate users. Only TACACS servers are supported.
A. DHCP snooping commands are not available until the feature is enabled with the feature dhcp- snooping command.
B. When you enable the DHCP snooping feature， the switch begins building and maintaining the DHCP snooping binding database.
C. The switch will not validate DHCP messages received or use the DHCP snooping binding database to validate subsequent requests from untrusted hosts until DHCP snooping is enabled globally and for each specific VLAN.
D. Globally disabling DHCP snooping removes all DHCP snooping configuration on the switch.
E. Globally disabling DHCP snooping does not remove any DHCP snooping configuration or the configuration of other features that are dependent upon the DHCP snooping feature.
A. The AED is responsible for sending all unicast traffic in a site， while either node in a site can transmit multicast and broadcast.
B. The AED is responsible for load balancing all traffic for all VLANs across the transport network.
C. The AED is responsible for handling all unicast， broadcast， and multicast traffic for a given VLAN within a site.
D. The AED is responsible for MAC address dispute contention for a given VLAN.
A. The verify command will validate commands entered for syntax errors.
B. The save command will save the commands entered to the startup configuration.
C. The network administrator can perform a dry-run ACL configuration by verifying the configuration against the hardware and software resources available before applying it.
D. Configuration sessions can be saved and resumed at any time， even after upgrading NX-OS Software on the switch with ISSU.
E. Configuration sessions are global for all VDCs on the Nexus 7000.
A. Improves convergence of the multicast network due to enhanced RPF checks
B. Simplifies the number of control plane protocols over other RP redundancy methods
C. Eliminates the use of Protocol Independent Multicast （PIM） in the topology
D. Increases the administrative distances in Multicast Source Discovery Protocol （MSDP） configuration
最新試題
Application Control Engine （ACE） can check the health of servers and server farms by configuring health probes （which are sometimes referred to as keepalives）. A probe can be one of many types. Which are valid ACE probes？ （）
An administrator creates a vNIC and assigns it to Fabric A with the fabric failover feature enabled. Which statement is true？（）
Which are valid statements about Cisco Virtual Interface Card （VIC）？ （）
A Cisco Application Control Engine Appliance （ACE） non-admin context does not support "sticky" configuration. What is the reason for this issue？（）
Which GSS "source access list" is used to allow access to GSS by clients when GSS is being used as the DNS？（）
Given the following output： san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24：0c：00：0d：ec：d3：5c：00 Admin port mode is NP， trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] ： fc2/3 Member[2] ： fc2/4 What does "Speed is 8 Gbps" indicate？（）
Which statements are true regarding the Cisco UCS fabric failover feature？ （）
Refer to the exhibit.Your company requires a Cisco UCS configuration that will， at a minimum， allow the configuration in the provided exhibit. Which Cisco UCS components will meet the requirement？（）
What is the use of an "all configuration" backup in Cisco UCS？（）
What is required for Cisco UCS C-Series rack server integration with Cisco UCS Manager？（）