A Cisco switch has this configuration for a port channel connecting to an ESXi using dual NICs and is intended for use with an N1Kv.
Interface fastethernet 1/10
Switchport mode trunk
Switchport trunk allowed vlan all
Channel-group 10 mode on
No shut
Interface fastethernet 1/11
Switchport mode trunk
Switchport trunk allowed vlan all
Channel-group 10 mode on
No shut
Interface port-channel 10
Switchport mode trunk
Switchport allowed vlan all
No shut
Which Port Channel configuration must be used on the Nexus 1000v port-profile？（）
A. MAC pinning
B. Cisco Discovery Protocol pinning
C. Mode On
D. Mode Active
E. No port channel configuration
您可能感興趣的試卷
你可能感興趣的試題
A. perform flow lookups
B. intercept packets on service enabled ports
C. run packets through the vPath flow manager
D. classify the packets
E. flow manager emits an action for the packets
F. enforce the action determined by the flow manager
Given the following configuration， what command can be used to determine the physical path that traffic will be sent out upon？（）
Port-profile type Ethernet name vm-data
Switchport mode trunk
Switchport trunk allowed vlan 200-210
Channel-group auto mode on mac-pinning
State enabled
Vmware port-group
No shut
Port-profile type vethernet name vlan-200
Switchport mode access Switchport vlan 200
State enabled Vmware port-group No shut
A. module vem X execute vemcmd show trunk
B. show module 3 internal pinning
C. module vem X execute vemcmd show port
D. show module vem mapping
E. show interface vethX pinning
A. Upstream switch
B. Virtual Supervisor Module
C. VMware distributed switch
D. VMware vSwitch
E. Service virtual machine
A. All vEthernet ports are trusted， and all Ethernet ports such as uplinks and port channels are trusted.
B. All vEthernet ports are not trusted， and all Ethernet ports such as uplinks and port channels are not trusted.
C. All vEthernet ports are trusted and all Ethernet ports such as uplinks and port channels are not trusted.
D. All vEthernet ports are not trusted and all Ethernet ports such as uplinks and port channels are trusted.
n1kv-l3（config）# show lacp offload status
Current Status ： Enabled
Running Config Status ： Enabled
Saved Config Status ： Disabled
What two facts does the output signify？ （）
A. LACP is enabled on the Nexus 1000v.
B. LACP will be offloaded to the upstream switch.
C. LACP will be negotiated to the VM.
D. LACP is negotiated by the VSM.
E. LACP is negotiated by the VEM in all instances.
最新試題
Application Control Engine （ACE） can check the health of servers and server farms by configuring health probes （which are sometimes referred to as keepalives）. A probe can be one of many types. Which are valid ACE probes？ （）
In a Cisco Unified Computing System， where are SAN port channels connected to？（）
Which GSS "source access list" is used to allow access to GSS by clients when GSS is being used as the DNS？（）
Which statement is true about "full state backup" in a Cisco Unified Computing System？（）
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）
Refer to the exhibit. According to the equipment tab in Cisco UCS Manager， which is true？（）
Given a Cisco Unified Computing System， which is a valid port type in end-host mode？（）
From the Cisco UCS CLI， how do you verify which uplink ports a blade server is using for its network connectivity？（）
Which statement is true regarding Backup tasks in Cisco UCS？（）
Which two statements about end-host mode in SAN connectivity in a Cisco UCS environment are true？ （）