This graphic shows the results of an attempt to open a Telnet connection to router ACCESS1 from router Remote27. Which of the following command sequences will correct this problem? （）
A. ACCESS1(config)# line console 0 ACCESS1(config-line)# password cisco
B. Remote27(config)# line console 0 Remote27(config-line)# login Remote27(config-line)# password cisco
C. ACCESS1(config)# line vty 0 4 ACCESS1(config-line)# login ACCESS1(config-line)# password cisco
D. Remote27(config)# line vty 0 4 Remote27(config-line)# login Remote27(config-line)# password cisco
E. ACCESS1(config)# enable password cisco
F. Remote27(config)# enable password cisco
您可能感興趣的試卷
你可能感興趣的試題
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?（）
A. The OSPF area is not configured properly.
B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.
A. A remote physical layer problem exists.
B. The host NIC is not functioning.
C. TCP/IP has not been correctly installed on the host.
D. A local physical layer problem exists.
A. 24
B. 4
C. 3
D. 16
A. The Gallant router has the wrong LMI type configured
B. Inverse ARP is providing the wrong PVC information to the Gallant router
C. The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
D. The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
E. The IP address on the serial interface of the Attalla router is configured incorrectly
A. point-to-point
B. broadcast multi-access
C. nonbroadcast multi-access
D. nonbroadcast multipoint
E. broadcast point-to-multipoint
最新試題
While troubleshooting a network problem,a technician discovers that the current copy of the Cisco IOS is outdated and needs to be updated.Which of the following commands would the technician issue to replace the Cisco router IOS with the newer version?（）
At which layer of the OSI model is RSTP used to prevent loops?（）
A network administrator is planning a network installation for a large organization.The design requires 100 separate subnetworks,so the company has acquired a Class B network address.What subnet mask will provide the 100 subnetworks required, if 500 usable host addresses are required per subnet?（）
Which address is the IPV6 all-RIP-routers muticast group address that is used by RIPng as the destaion address?（）
A router receives information about network 192.168.10.0/24 from multiple sources.What will the router consider the most reliable information about the path to that network?（）
What is the default administrative distance of OSPF?（）
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
After the show ip route command has been entered,the follwing routes are displayed.Which route will not be entered into the routing table of a neighboring router?（）
Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers?（）
Three access ports have been installed and configured to a small office.What term defines the wireless topology?（）