A.In a 6to4 tunnel, the first two bytes of the IPv6 address will be 0x2002 and the next four byteswill be the hexadecimal equivalent of the IPv4 address
B.In a 6to4 tunnel, the IPv4 address 192.168.99.1 would be converted to the2002:1315:4463:1::/64 IPv6 address
C.In a 6to4 tunnel, the IPv4 address 192.168.99.1 would be converted to the 2002:c0a8:6301::/48IPv6 address
D.In a 6to4 tunnel, the first two bytes of the IPv6 address will be locally derived and the next twobytes will be the hexadecimal equivalent of the IPv4 address
E.In a 6to4 tunnel, the IPv4 address 192.168.99.1 would be converted to the 2002:c0a8:6301::/16IPv6 address
您可能感興趣的試卷
你可能感興趣的試題
A.6to4 is a manual tunnel method
B.Prepending a reserved IPv6 code to the hexadecimal representation of 192.168.0.1 facilitates6to4 tunneling
C.Each 6to4 site receives a /48 prefix in a 6to4 tunnel
D.2002::/48 is the address range specifically assigned to 6to4
E.Prepending 0x2002 with the IPv4 address creates an IPv6 address that is used in 6to4tunneling
A.Only OSPF version 3 can be utilized for routing IPv4 and IPv6
B.IPv4 and IPv6 networks can be routed simultaneously
C.IPv6 can be routed using the same routing protocol versions as IPv4
D.A router routing for IPv6 and IPv4 must convert IPv4 packets to IPv6 packets to route them
E.None of the other alternatives apply
A.192.168.30.1:0:0:0:0:0:0
B.0:0:0:0:0:0:192.168.30.1
C.::192.168.30.1
D.C0A8:1E01::
E.192.168.30.1::
F.::C0A8:1E01
A.The route table is cleared. Then the OSPF neighbors are reformed
B.The OSPF adjacencies are cleared and initiated again
C.The OSPF database is repopulated and then the shortest path first (SPF) algorithm isperformed.
D.The shortest path first (SPF) algorithm is performed on the LSA database
E.None of the other alternatives apply
Refer to the exhibit. What two statements are true?()
A.The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808
B.This is the designated router (DR) on the FastEthernet 0/0 link
C.Interface FastEthernet 0/0 was configured with the ipv6 ospf 1 area 1 command
D.OSPF version 2 has been enabled to support IPv6
E.The output was generated by the show ip interface command
最新試題
As a network engineer, do you know for what purpose SDM uses Security Device Event Exchange(SDEE)?()
A new router was configured with the following commands:The configuration above was found on an Internet Service Provider’s (ISP) Multiprotocol LabelSwitching (MPLS) network. What is its purpose?()
Router NetworkTut is configured as shown below:Given the above configuration, which statement is true?()
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions, you will need to referto the SDM and the topology, neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define?()
Drag each element of the Cisco IOS Firewall Feature Set from the above and drop onto itsdescription on the below.
Which statement about PPPoA configuration is correct?()
As a network engineer, study the exhibit carefully. Router Net is unable to establish an ADSLconnection with its provider. Which action would correct this problem?()
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec, which two parameters are required when defining the tunnel interfaceinformation?()
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions, you will need to referto the SDM and the topology, neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete?()
Refer to the exhibit. Which two statements about the AAA configuration are true?()