A.Trunk
B.Isolated
C.Primary
D.Community
E.Promiscuous
F.None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. The user who is connected to interface FastEthernet 0/1 is on VLAN 10 andcannot access network resources. On the basis of the information in the exhibit， which commandsequence would correct the problem？（）
A.SW1（config）# interface fastethernet 0/1 SW1（config-if）# no shut
B.SW1（config）# interface fastethernet 0/1 SW1（config-if）# switchport mode access SW1（config-if）# switchport access vlan 10
C.SW1（config）# vlan 10 SW1（config-vlan）# state active
D.SW1（config）# interface fastethernet 0/1 SW1（config-if）# switchport mode access
E.SW1（config）# vlan 10 SW1（config-vlan）# no shut
You work as a network Technician. A new workstation has consistently been unable to obtain anIP address from the DHCP server when the workstation boots. Older workstations function
normally， and the new workstation obtains an address when manually forced to renew its address.
What should be configured on the switch to allow the workstation to obtain an IP address at boot？（）
A.UplinkFast on the switch port connected to the server
B.BackboneFast on the switch port connected to the server
C.PortFast on the switch port connected to the workstation
D.trunking on the switch
A.Ports in VLAN 5
B.Utilization
C.VLAN information on port 0/5
D.Filters
E.MTU and type
Refer to the exhibit. On the basis of the output generated by the show commands， which twostatements are true？（）
A.All interfaces on the switch have been configured as access ports
B.Because it has not been assigned to any VLAN， interface gigabitethernet 0/1 does not appearin the show vlan output
C.Because it is configured as a trunk interface， interface gigabitethernet 0/1 does not appear inthe show vlan output
D.There are no native VLANs configured on the trunk
E.VLAN 1 will not be encapsulated with an 802.1q header
F.VLAN 2 will not be encapsulated with an 802.1q header
Refer to the exhibit. Based upon the output of show vlan on switch CAT2， what can we concludeabout interfaces Fa0/13 and Fa0/14？（）
A.that interfaces Fa0/13 and Fa0/14 are in VLAN 1
B.that interfaces Fa0/13 and Fa0/14 are down
C.that interfaces Fa0/13 and Fa0/14 are trunk interfaces
D.that interfaces Fa0/13 and Fa0/14have a domain mismatch with another switch
E.that interfaces Fa0/13 and Fa0/14have a duplex mismatch with another switch
最新試題
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
Authentication is the process of determining if a user or identity is who they claim to be. Refer tothe exhibit. Which statement about the authentication process is correct？（）
Drag and drop question. The upper gives the MPLS functions， the bottom describes the planes.Drag the above items to the proper location at the below
IPSec VPN is a widely-acknowledged solution for enterprise network. Which three IPsec VPNstatements are true？（）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete？（）
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN？（）
As a network engineer， do you know for what purpose SDM uses Security Device Event Exchange（SDEE）？（）
cisco ios command to interface dialer 0
Drag and drop each function on the above to the hybrid fiber-coaxial architecture component that itdescribes on the below.