A.A BPDU Guard port should only be configured on ports with PortFast enabled
B.BPDU Guard and PortFast should not be enabled on the same port.
C.BPDU Guard is used to ensure that superior BPDUs are not received on a switch port
D.A BPDU Guard port receiving a BPDU will go into err-disable state
E.A BPDU Guard port receiving a BPDU will be disabled
F.BPDU Guard can be enabled on any switch port
您可能感興趣的試卷
你可能感興趣的試題
A.All traffic is tagged with a specific VLAN ID from the VLAN of the attacker and is now viewable
B.Clients will forward packets to the attacking device, which will in turn send them to the desireddestination but not before recording the traffic patterns
C.All traffic is redirected to the VLAN that the attacker used to flood the CAM table
D.All traffic is flooded out all ports and an attacker is able to capture all data
E.None of the other alternatives apply
A.MAC spoofing
B.VLAN hopping
C.MAC address flooding
D.DHCP flooding
E.Session hijacking
A.Enable BPD guard
B.Disable CDP on ports where it is not necessary
C.Place unused ports in a common unrouted VLAN
D.Prevent automatic trunk configuration
E.Implement port security
Refer to the exhibit. Based upon the configuration, you need to understand why the policy routingmatch counts are not increasing. Which would be the first logical step to take?Select the bestresponse.()
A.Confirm if there are other problematic route-map statements thatprecede divert
B.Check the access list for log hits
C.Check the routing table for 212.50.185.126
D.Remove any two of the set clauses(Multiple set clause entries will cause PBR to use therouting table.)
Study the following graphic carefully Host1 and Host2, which belong to different VLANs, are in thesame subnet. According to the information displayed, which description is correct when trying toping from host to host?()
A.A trunk port should be configured on the link between CK-SW1 and CK-SW2 to pingsuccessfully
B.The two hosts should be in the same VLAN in order to ping successfully
C.A Layer 3 device is a must in order for the ping command to be successful
D.The ping command will be successful without any further configuration changes
最新試題
Drag the DSL technologies on the left to their maximum(down/up) data rate values on the below.
In computer security, AAA stands for authentication, authorization and accounting. Which optionabout the AAA authentication enable default group radius enable command is correct?()
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions, you will need to referto the SDM and the topology, neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define?()
Drag each element of the Cisco IOS Firewall Feature Set from the above and drop onto itsdescription on the below.
cisco ios command to interface dialer 0
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.
Drag and drop question. The upper gives the MPLS functions, the bottom describes the planes.Drag the above items to the proper location at the below
Drag the correct statements about MPLS-based VPN on the left to the boxes on the right.(Not allstatements will be used)
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions, you will need to referto the SDM and the topology, neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete?()
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN?()