A.Mismatched EtherChannel protocol
B.Mismatched EtherChannel port selection
C.Mismatched EtherChannel distribution algorithm
D.Mismatched trunk mode
E.Mismatched native VLAN
F.Mismatched link speed
您可能感興趣的試卷
你可能感興趣的試題
A.NAT mapping
B.NAT overloading
C.NAT caching
D.Static NAT
E.Dynamic NAT
F.Overlapping NAT
A.The network is load balancing among different members of the VRRP group
B.The default hello timers are 1 second
C.The interface IP address is being used as the virtual IP address
D.There are several routers in the group simultaneously forwarding traffic for the group
E.It is a Cisco Proprietary protocol
F.The default hello timers are 3 seconds
A.A routed port does not run STP or DTP
B.A routed port is considered to be in a down state if it is not operational at both Layer 1 andLayer 2
C.An SVI is considered to be in a down state if it is not operational at both Layer 1 and Layer 2
D.An SVI is considered to be in a down state only when none of the ports in the correspondingVLAN are active
E.An SVI port does not run 5TP or DTP
F.To create a trunk， an SVI can be logically divided into subinterfaces
A.The interface you configured for AutoQoS is set to half-duplex
B.AutoQoS was configured on only one end of the link
C.The interface you configured for AutoQoS has no IP address
D.The interface’s bandwidth is not correctly configured
E.CEF is not enabled on the interface
F.You enabled AutoQoS on the interface but forgot to enable globally first
A.Spanning Tree Protocol
B.Cabling
C.Frame forwarding
D.Packet forwarding
E.EtherChannel
F.Routing protocols
最新試題
Router NetworkTut is configured as shown below：Given the above configuration， which statement is true？（）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete？（）
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
Drag and drop each management protocol on the above to the correct category on the below.
Authentication is the process of determining if a user or identity is who they claim to be. Refer tothe exhibit. Which statement about the authentication process is correct？（）
Match the xDSL type on the above to the most appropriate implementation on the below.
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
Network Topology Exhibit：Configuration Exhibit：NET（config）# access-list 112 deny icmp any any echo logNET（config）# access-list 112 deny imp any any redirect logNET（config）# access-list 112 deny icmp any any mask-request logNET（config）# access-list 112 permit icmp any 10.1.1.0 0.0.0.255NET（config）# interface Fa0/1NET（config-if）# ip access-group 112 inYou work as a network administrator at networkTut.com， study the exhibit carefully. Theconfiguration has been applied to router NET to mitigate the threat of certain types of ICMPbasedattacks while allowing some ICMP traffic to the corporate LAN to work. However， the configurationis incorrect. On the basis of the information in the exhibit， which configuration option wouldcorrectly configure router NET？（）
Drag and drop each function on the above to the hybrid fiber-coaxial architecture component that itdescribes on the below.
In computer security， AAA stands for authentication， authorization and accounting. Which optionabout the AAA authentication enable default group radius enable command is correct？（）