Which MST configuration statement is correct？ （）
A. MST configurations can be propagated to other switches using VTP.
B. After MST is configured on a Switch， PVST+ operations will also be enabled by default.
C. MST configurations must be manually configured on each switch within the MST region.
D. MST configurations only need to be manually configured on the Root Bridge.
E. MST configurations are entered using the VLAN Database mode on Cisco Catalyst switches.
您可能感興趣的試卷
你可能感興趣的試題
A. MST00
B. MST01
C. the last MST instance configured
D. none
A. Region name
B. Configuration revision number
C. VLAN instance map
D. IST STP BPDU hello timer
E. CST instance map
F. PVST+ instance map
Which of the following specification will allow you to： associate VLAN groups to STP instances so you can provide multiple forwarding paths for data traffic and enable load balancing？ （）
A. IEEE 802.1d （STP）
B. IEEE 802.1s （MST）
C. IEEE 802.1Q （CST）
D. IEEE 802.1w （RSTP）
Which of the following specifications is a companion to the IEEE 802.1w Rapid Spanning Tree Protocol （RSTP） algorithm， and warrants the use multiple spanning-trees？ （）
A. IEEE 802.1s （MST）
B. IEEE 802.1Q （CST）
C. Cisco PVST+
D. IEEE 802.1d （STP）
E. None of the other alternatives apply
pany uses MSTP within their switched LAN.
What is the main purpose of Multiple Instance Spanning Tree Protocol （MSTP）？（）
A. To enhance Spanning Tree troubleshooting on multilayer switches
B. To reduce the total number of spanning tree instances necessary for a particular topology
C. To provide faster convergence when topology changes occur in a switched network
D. To provide protection for STP when a link is unidirectional and BPDUs are being sent but not received
E. None of the other alternatives apply
最新試題
Which statement is correct about RSTP port roles？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）