Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configur ation statement should be included on router R4 to advertise a default route to its neighbors?（）
A. R4(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1
B. R4(config)# ip default - network 10.0.0.0
C. R4(config - router)# default -information originate
D. R4(conf ig)# ip route 10.0.0.0 255.0.0.0 10.1.1.1
您可能感興趣的試卷
你可能感興趣的試題
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.
Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
A. By not enabling NAT on the I Psec tunnel interface
B. By not enabling NAT on the GRE tunnel interface
C. By configuring the NAT - referenced ACL to not permit the Enterprise traffic
D. By asking the ISP to perform NAT in the cloud
A. The method of choosing an OSPF router ID
B. Verification checks that must be validated before two routers can become OSPF neighbors
C. Support for route tags
D. Support for multiple instances per inter face
Router R1 lists the following output from a show command. Which of the following is true about R1?（）
R1# show ip v6 interface f0/0
FastEthernet0/0 is up, line protocol is up
IPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456
No Virtual link - local address(es):
Global unicast address(es):
2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]
Jo ined group address(es):
FF02::1
FF02::2
FF02::1:FF:12:3456
A. R1's solicited node multicast address is FF02::1:FF:12:3456.
B. R1's 2000::4:213:19FF:FE12:3456 address is a global unicast with all 128 bits statically configured.
C. Address FF02::2 is R1's solicited node multicast.
D. R1's solicited node multicast, not listed in this output, would be FF02::213:19FF:FE12:3456.
A. Automatic 6to4
B. Manually configured tunnel
C. ISATAP
D. GRE
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）
B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
A. This router has set the Weight of this route to 10.
B. This router's BGP table lists this route as an iBGP route.
C. This router's MED has been set to 10.
D. This router's BGP table lists an AS_Path length of 10 for this route.
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）
D 2000::/64 [90/1422516]
via FE80::213:19FF:FE7B:5026, Serial0/0/
1
C 2000:0:0:1::/64 [0/0]
via Serial0/0/1, directly connected
L 2000::1:213:19FF:FE7B:5004/128 [0/0]
via Serial0/0/1, receive
A. Route 2000::/64 will be redistributed.
B. Route 2 000:0:0:1::/64 will be redistributed.
C. Route 2000:1:213:19FF:FE7B:5004/128 will be redistributed.
D. No routes will be redistributed because of the omission of the subnets parameter of the redistribute command.
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）
Network Next Hop Metric LocPrf Weight Path
*> 3.3.3.3 0 0 1 1 1 1 2
18 i
A. The Enterprise likely uses ASN 1.
B. The neighboring ISP likely uses ASN 1.
C. The route has been advertised through ASN 1 multiple times.
D. Router Ent1 will add another ASN to the AS_Path before advertising this route to its iBGP peer (4.4.4.4).
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）
ipv6 router eigrp 1
ipv6 unicast- routing
interface f0/0
ipv6 address 2000::1/64
ipv6 eigrp 1
interface s0/0/0
ipv6 address 2001::/64 eui - 64
ipv6 eigrp 1
A. EIGRP works on F0/0 and S0/0/0 without further configuration
B. EIGRP works with the addition of one command: a no shutdown command in EIGRP router configuration modE
C. EIGRP works with the addition of one command: an eigrp router - id command in EIGRP router configurat ion modE
D. EIGRP for IPv6 needs at least two more configuration commands before it works on R1
A. area IDs
B. process IDs
C. router IDs
D. hello timers
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）
ipv6 router ospf 1
ipv6 unicast- routing
interface f0/0
ipv6 address 2000 ::1/64
ipv6 ospf 1 area 1
interface s0/0/0
ipv6 address 2001::/64 eui - 64
ipv6 ospf 1 area 0
A. OSPF works on F0/0 and S0/0/0 without further configuration
B. OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modE
C. OSPF works with the addition of one command: an router - id command in OSPF router configuration modE
D. OSPFv3 needs at least two more configuration commands before it works on R1
最新試題
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
Which of the following features work the same in both RIP- 2 and RIPng?（）
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Which of the following answers lists a multicast IPv6 address?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）