A Company switch was configured as shown below：
switchport mode access switchport port-security
switchport port-security maximum 2
switchport port-security mac-address 0002.0002.0002
switchport port-security violation shutdown
Given the configuration output shown above，
what happens when a host with the MAC address of 0003.0003.0003 is directly connected to the switch port？ （）
A. The host will be allowed to connect.
B. The port will shut down.
C. The host can only connect through a hub/switch where 0002.0002.0002 is already connected.
D. The host will be refused access.
E. None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
VLAN maps have been configured on switch R1.
Which of the following actions are taken in a VLAN map that does not contain a match clause？ （）
A. Implicit deny feature at end of list.
B. Implicit deny feature at start of list.
C. Implicit forward feature at end of list
D. Implicit forward feature at start of list.
Refer to the exhibit. The web servers WS_1 and WS_2 need to be accessed by external and internal users. For security reasons， the servers should not communicate with each other，
although they are located on the same subnet. The servers do need， however， to communicate with a database server located in the inside network.
What configuration will isolate the servers from each other？ （）
A. The switch ports 3/1 and 3/2 will be defined as secondary VLAN community ports. The ports connecting to the two firewalls will be defined as primary VLAN promiscuous ports.
B. The switch ports 3/1 and 3/2 and the ports connecting to the two firewalls will be defined as primary VLAN promiscuous ports.
C. The switch ports 3/1 and 3/2 and the ports connecting to the two firewalls will be defined as primary VLAN community ports.
D. The switch ports 3/1 and 3/2 will be defined as secondary VLAN isolated ports. The ports connecting to the two firewalls will be defined as primary VLAN promiscuous ports.
pany is implementing 802.1X in order to increase network security. In the use of 802.1X
access control，
which three protocols are allowed through the switch port before authentication takes place？ （）
A. EAP-over-LAN
B. EAP MD5
C. STP
D. protocols not filtered by an ACL
E. CDP
F. TACACS+
Refer to the exhibit.
What will happen to traffic within VLAN 14 with a source address of 172.16.10.5？（）
A. The traffic will be forwarded to the router processor for further processing.
B. The traffic will be dropped.
C. The traffic will be forwarded to the TCAM for further processing.
D. The traffic will be forwarded without further processing.
The Company security administrator wants to prevent DHCP spoofing.
Which statement is true about DHCP spoofing operation？（）
A. DHCP spoofing and SPAN cannot be used on the same port of a switch.
B. To prevent a DHCP spoofing， the DHCP server must create a static ARP entry that cannot be updated by a dynamic ARP packet.
C. To prevent a DHCP spoofing， the switch must have DHCP server services disabled and a static entry pointing towards the DHCP server.
D. DHCP spoofing can be prevented by placing all unused ports in an unused VLAN.
E. None of the other alternatives apply.
最新試題
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
What two things will occur when an edge port receives a BPDU？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）