Refer to the diagram. Which OSPF configuration command is required to configure Area 3 a s atotally stubby area?（）
A. On the ABR router ospf 10 area 3 stub
B. On all Area 3 routers router ospf 10 area 3 stub
C. On all Area 3 routers router ospf 10 area 3 stub no - summary
D. On the ABR router ospf 10 area 3 nssa
E. On the ABR rou ter ospf 10 area 3 stub no - summary
您可能感興趣的試卷
你可能感興趣的試題
The Dev - 1 and Dev -3 routers are OSPF neighbors over the Ethernet 0/0 connection. Based on the show ip ospf neighbor output from the Dev - 1 and Dev - 3 routers, which statement is true?（）
A. Dev - 1 is the DR because it has a lower OSPF router ID
B. Dev - 3 is the DR because it has a higher OSPF router priority
C. Both Dev - 1 and Dev - 3 are using the def ault OSPF router priority
D. Dev - 3 is the DR because it has a lower OSPF router ID
E. Dev - 1 is the DR because it has a higher OSPF router priority
During a recent OSPF election among three routers, RTA was elected the DR and RTB was elected the BDR, as seen in the graphic. Assume that RTA fails, and that RTB takes the place of
the DR whi le RTC becomes the new BDR. What will happen when RTA comes back online？（）
A. A new election will take place establishing an all new DR and BDR based on configured priority levels and MAC addresses.
B. RTA will take the place of DR immediately upon esta blishing its adjacencies.
C. RTA will take the place of DR only if RTB fails.
D. RTA will take the place of DR only if both RTB and RTC fail.
A. show ip protocol
B. show ip ospf
C. sho w ip ospf database
D. show ip ospf interface
Refer to the output. What IOS command produces this output？（）
A. show i p ospf
B. show ip ospf interface
C. show ipv6 ospf interface
D. show ipv6 ospf
Into which two types of areas would an area border router (ABR) inject a default route?（）
A. stub
B. the autonomous system of an exte rior gateway protocol (EGP)
C. NSSA
D. totally stubby
E. the autonomous system of a different interior gateway protocol (IGP)
F. area 0
最新試題
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64