Study the exhibit shown below carefully. A Cisco Aironet Wireless LAN Client Adapter has been installed and configured through the ADU on the PC. The Aironet System Tray Utility （ASTU） has been enabled during the installation and the icon appears in the system tray area in the lower right of the desktop as shown：
What is the significance of this icon？ （）
A. It indicates that the client adapter is not associated to an access point or another client.
B. It indicates that the radio of the client adapter is disabled.
C. It indicates that the client adapter is associated to an access point or another client， but the user is not EAP authenticated.
D. It indicates that the client adapter is associated to an access point or another client， that theuser is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is poor.
E. It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is fair.
F. It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is excellent or good.
您可能感興趣的試卷
你可能感興趣的試題
Which three statements are true about implementing wireless LANs in the Company network using Cisco devices？（）
A. Antenna power is a relative value reference to dBi.
B. LWAPP allows encrypted communications between lightweight access points and WLAN controllers.
C. Characteristics of antennas are directionality， gain， and polarization.
D. Power over Ethernet （PoE） is only available when a WLAN controller is integrated into the network.
E. The WLAN solution Engine （WLSE） is used to control lightweight access points.
F. One of the advantages of the lightweight WLAN solution is that the devices act indepently.
Under which three conditions does a client initiate roaming between wireless cells in the Company WLAN？ （）
A. The access point has broadcast too many SSIDs.
B. The wireless client has missed too many beacons from the access point.
C. The maximum data retry count， initiated by the wireless client， is exceeded.
D. The wireless client has reduced the data rate.
E. The access point has requested client reauthentication.
F. The wireless client has missed too many IAPP （Inter Access Point Protocol） updates.
Refer to the exhibit. The wireless user is moving from right to left towards AP2.
What are three reasons that the wireless client would initiate roaming？（）
A. The minimum data retry count from AP1 is exceeded.
B. The maximum data retry count from AP1 is exceeded.
C. The client has missed too many beacons from AP1.
D. The client data rate from AP1 has been reduced.
E. The client has received too many beacons from AP2.
F. The client data rate from AP2 has been increased.
Refer to the exhibit.
Which protocol establishes an optimal path to the root in a wireless mesh network？ （）
A. Adaptive Wireless Path （AWP）
B. WLAN Quality of Service （WQoS）
C. Lightweight Access Point Protocol （LWAPP）
D. 802.1Q WLAN trunking protocol
E. Layer 2 Roaming （IAPP）
Refer to the exhibit.
Which statement is true about the repeater access point that is deployed in this wireless network？（）
A. The repeater access point should use a different SSID than the SSID configured on the parent access point.
B. The repeater access point reduces the throughput in half because it receives and then retransmits each packet on the same channel.
C. The repeater access point requires a 10 percent channel overlap with channel of the root access point.
D. The repeater access point should use a different WEP encryption method than the WEP encryption that is enabled on the parent access point.
最新試題
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）