Examine the above configuration. What does the route map named test accomplish?（）
A. permits only the 10.0.0.0/8 prefix to be advertised to the 10.1.1.1 neighbor
B. marks all prefixes received fro m the 10.1.1.1 neighbor with a MED of 200
C. marks the 10.0.0.0/8 prefix advertised to the 10.1.1.1 neighbor with a MED of 200
D. permits only the 10.0.0.0/8 prefix to be received from the 10.1.1.1 neighbor
E. marks all prefixes advertised to the 10.1.1 .1 neighbor with a MED of 200
F. marks the 10.0.0.0/8 prefix received from the 10.1.1.1 neighbor with a MED of 200
您可能感興趣的試卷
你可能感興趣的試題
A. BGP uses TCP port 179.
B. BGP ensures reliability of updates by using the reliable transport services of TCP.
C. The network command with the mask option never insta lls a prefix into the BGP table unless there is a matching prefix exists in the IP route table.
D. A TCP connection is required before exchanging updates.
E. BGPuses notification and the update messages to establish and maintain the BGP neighbor relati onship.
Refer to the exhibit. Which statement is true about the 6.6.6.0/24 prefix?（）
A. The command neighbor send -community is configured on BGP neighbor 10.10.23.3.
B. If another path advertises the 6.6.6.0/24 path and has the default local preference, that path is more preferred.
C. Route 6.6.6.0/24 is learned by an IBGP peer.
D. The route 10.10.23.3 is not being advertised to other BGP neighbors.
A. Only one IPv6 address can be assigned to each interface.
B. IPv6 hosts use anycast addresses to assign IP addresses to interfaces.
C. Each host can a utoconfigure its address without the aid of a DHCP server.
D. Only one IPv6 address is assigned per node.
Refer to the exhibit. Autonomous systems 200 and 300 have EBGP sessions established with their directly connected routers in au tonomous system 100. IGP has been configured on all routers in autonomous system 100 and they successfully exchange routing updates. Traffic originated in autonomous system 200 cannot reach the destination autonomous system 300. What configuration shoul d be done on the routers in autonomous system 100 in order for the traffic coming from autonomous system 200 to be forwarded to autonomous system 300?（）
A. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned off.
B. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned on.
C. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned on.
D. IBGP session mu st be established between routers R1 and R3, and the synchronization must be turned off.
E. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned off.
F. IBGP session must be established between routers R1 and R3, and the synchronization must be turned on.
Refer to the exhibit. By default, when RTB passes BGP advertisements from RTA about network 192.168.2.0 to RTC, what address will be listed as the next - hop address? （）
A. 10.1.1.2
B. 192.168.1.49
C. 10.1.1.1
D. 192.168.1.50
最新試題
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Which of the following features work the same in both RIP- 2 and RIPng?（）
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）