A. It must be issued before the network command to enable the OSPF pr ocess for IPv6.
B. It must be issued after the network command to enable the OSPF process for IPv6.
C. It must be issued in router global configuration mode to enable the OSPF process for IPv6.
D. It must be issued in interface configuration mode to ena ble the OSPF process for IPv6.
您可能感興趣的試卷
你可能感興趣的試題
In IPv6, the interfaces running OSPF can be configured with multiple ad dress prefixes.
Which statement is true about the IPv6 addresses that can be included into the OSPF process?" （）
A. Specific addresses can be selected using a prefix list.
B. Specific addresses can be selected using a route map.
C. Specific addresses cann ot be selected for importation into the OSPF process.
D. Specific addresses can be selected using an ACL.
A. The shortest path first (SPF) algorithm is performed on the LSA database.
B. The OSPF adjacencies are cleared and initiated again.
C. The OSPF database is repopulated. Then the shortest path first (SPF) algorithm is performed.
D. The route table is cleared. Then the OSPF neighbors are reformed.
A. all routers in a local segment
B. all routers in an autonomous system
C. all hosts in a local segment
D. all hosts in a particular multicast group
A. If a packet is sent to a multicast group address, the multicast frame contains the source multicast address.
B. A router does not have to be a member of a multicast group to receive multicast data.
C. A router must be a member of a multicast group to send to the group.
D. A router does not have to be a member of a multicast group to send to the group.
E. If a packet is sent to a multicast group address, all members of the multicast group will rece ive it.
F. A router must be a member of a multicast group to receive multicast data.
Refer to the exhibit. What two statements are true?（）
A. This is the designated router (DR) on the FastEthernet 0/0 link.
B. The output was generated by the show ip interface c ommand.
C. The router was configured with the commands:r outer ospf 1 network 172.16.6.0 0.0.0.255 area 1
D. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.
E. Interface FastEthernet 0/0 was configured with the ipv6 o spf 1 area 1 command.
F. OSPF version 2 has been enabled to support IPv6.
最新試題
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
Which of the following answers lists a multicast IPv6 address?（）
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?（）
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）