A. Spanning Tree Protocol （STP）
B. Delay reduction
C. Hot Standby Routing Protocol （HSRP）
D. Dynamic routing protocols
E. Quality of Service （QoS）
F. Jitter management
您可能感興趣的試卷
你可能感興趣的試題
What can be determined about the HSRP relationship from the displayed debug output？ （）
A. Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router 172.16.11.111.
B. Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router 172.16.11.112.
C. The IP address 172.16.11.111 is the virtual HSRP router IP address.
D. The IP address 172.16.11.112 is the virtual HSRP router IP address.
E. The nonpreempt feature is enabled on the 172.16.11.112 router.
F. The preempt feature is not enabled on the 172.16.11.111 router.
Examine the router output above.
Which two items are correct？ （）
A. The local IP address of Router A is 10.1.0.6.
B. The local IP address of Router A is 10.1.0.20.
C. If Ethernet 0/2 goesdown， the standby router will take over.
D. When Ethernet 0/3 of RouterA comes back up， the priority will become 105.
E. Router A will assume the active state if its priority is the highest.
Refer to the exhibit. Based upon the debug output that is shown，
which three statements about HSRP are true？（）
A. The router with IP address 172.16.11.111 haspreempt configured.
B. The final active router is the router with IP address 172.16.11.111.
C. The router with IP address 172.16.11.112 has nonpreempt configured.
D. The priority of the router with IP address 172.16.11.112 is preferred over the router with IP address 172.16.11.111.
E. The router with IP address 172.16.11.112 is using default HSRP priority.
F. The IP address 172.16.11.115 is the virtual HSRP IP address.
Refer to the exhibit.
Which two problems are the most likely cause of the exhibited output？（）
A. transport layer issues
B. VRRP misconfiguration
C. HSRP misconfiguration
D. physical layer issues
E. spanning tree issues
Examine the router output above. Which two items are correct？（）
A. The local IP address of Router A is 10.1.0.6.
B. The local IP address of Router A is 10.1.0.20.
C. If Ethernet 0/2 goesdown， the standby router will take over.
D. When Ethernet 0/3 of RouterA comes back up， the priority will become 105.
E. Router A will assume the active state if its priority is the highest.
最新試題
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Which three statements about STP timers are true？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）