A.Test the design on a pilot network for expected results prior to implementing on the production network.
B.Run a network audit to determine types of traffic in use on the network.
C.Launch campus updates into the production network and monitor impact to see if configuration changes are needed.
D.Create an interruption of data flow to determine test "back-door" access methods.
您可能感興趣的試卷
你可能感興趣的試題
A.a detailed physical and logical topology
B.a cost analysis of the implemented solution
C.detailed logs from the AAA and SNMP servers
D.results from audit testing of the implemented solution
A.having alternative addressing and VLAN schemes
B.having a rollback plan in case of unwanted or unexpected results
C.running a test script against all possible security threats to insure that the solution will mitigate all potential threats
D.isolating and testing each security domain individually to insure that the security design will meet overall requirements when placed into production as an entire system
A.a list of existing network applications currently in use on the network
B.network audit results to uncover any potential security holes
C.a planned Layer 2 design solution
D.a proof-of-concept plan
E.device configuration templates
A.detailed list of personnel assigned to each task within the plan
B.a Layer 2 spanning tree design topology
C.rollback guidelines
D.placing all unused access ports in VLAN 1 to proactively manage port security
E.enabling SNMP access to Cisco Discovery Protocol data for logging and forensic analysis
A.detailed VLAN information
B.an incident response plan
C.results of testing the new network configuration
D.an existing hierarchical network topology
E.a security policy for your organization
最新試題
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）