A router is running BGP and receives more than one route for a particular prefix. Assume all the routes for this prefix have the same attributes.
Which three path features would be reasons be for the rou ter to ignore some of the routes and not consider them as candidates for the best path?（）
A. paths from an internal BGP (iBGP) neighbor if the local autonomous system (AS) appears in the AS_PATH
B. paths for which the NEXT_HOP is inaccess ible
C. paths from an external BGP (eBGP) neighbor if the local autonomous system (AS) appears in the AS_PATH
D. paths for which the NEXT_HOP is accessible
E. paths that are marked as synchronized in the show ip bgp output
F. paths that are marked as not synchronized in the show ip bgp output
您可能感興趣的試卷
你可能感興趣的試題
You are a network techn ician, study the exhibit carefully. All multilayer switches are running PIM sparse mode. Host CKB and Host CKF are sending IGMPv2 join messages to their respective multilayer switches. Which description is correct?（）
A. Switches 1, 2, 3, and 6 will part icipate in the multicast tree once pruning has taken place.
B. Switches 2 and 6 will participate in the multicast tree once pruning has taken place.
C. Switches 1, 2, 3, and 6 will participate in the multicast tree.
D. The multicast server is the rendez vous point of the multicast tree.
A. IS - IS is capable of supporting IPv4 and IPv6.
B. IS - IS is only capable of supporting IPv4 and CLNS.
C. IS - IS routers use ES - IS hellos (ESH) to establish and to maintain neighbor relationships.
D. IS - IS routers run the Bellman - Ford algorithm against their LSDBs to pick the best paths.
E. Level 1 routers learn about paths within the area of which they are a part.
F. Level 2 routers learn about paths both within areas and between areas.
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）
A. Add the area 1 stub command on routers R1.
B. Add the always keyword to the default - information originate configuration command on router R2.
C. Remov e the default information originate configuration command from router R2 and place it on router R1.
D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
A. The BGP split - horizon rule specifies that routes learned via EBGP are never propagated to other IBGP peers.
B. The BGP split horizon rule specifies that routes learned via IBGP are never propagated to other IBGP peers.
C. A full - mesh IBGP requires that neighbor relationships be established between a ll BGP enabled routers in the autonomous system.
D. IBGP neighbors must be in different autonomous systems.
E. An EGP or static routing is required between IBGP neighbors.
Refer to the exhibit and the partial configuration on router R2. On router R4 all RIP routes are redistributed into the OSPF domain. A second redistribu tion is configured on router R2 using a route map. Based on the configuration on router R2, which EIGRP external routes will be present in the routing table of R1?（）
A. the routes originating from the RIP routing domain
B. the routes originating from the OSPF stub area
C. all OSPF inter and intra - area routes
D. all routes originating from RIP and OSPF routing domains
最新試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Which of the following features work the same in both RIP- 2 and RIPng?（）
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
Which of the following answers lists a multicast IPv6 address?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）