Refer to the exhibit. OSPF is configured on all routers in the network. Area 5 is configured as an NSSA areA. The RIPv2 routes are redistributed into the OSPF domain on router R5. What two types of LSAs will be originated by router R5?（）
A. type 1 Router LSA
B. type 2 Network LSA
C. type 3 Network Summary LSA
D. type 4 ASBR Summary LSA
E. type 5 AS External LSA
F. type 7 NSSA External LSA
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. What additional commands should be used to configure OSPF area 5 as a Totally Stubby area? （）
A. area 0 stub o n routers R4 and R5
B. area 5 stub on routers R4 and R5
C. area 5 stub no - summary on routers R4 and R5
D. area 0 stub no - summary on router R4 and area 5 stub no - summary on router R5
E. area 5 stub no - summary on router R4 and area 5 stub on router R5
Refer to the exhibit. Which statement is co rrect regarding the router configuration shown? （）
A. The router will rebroadcast any DHCP requests received by this interface out to all interfaces included in the ip helper - address commands.
B. The router will rebroadcast any UDP broadcasts received by this interface out to all interfaces included in the ip helper - address commands.
C. The router will unicast any DHCP requests received by this interface out to all addresses included in the ip helper - address commands.
D. This configuration will not do anything because the ip helper - address command needs to also be applied to the 192.168.23.1 IP address.
Look at the following exhibit. Which of the following correctly states the routes to be redistributed into OSPF? （）
A. The network 10.0.10.0/24 will be allowed and assigned a metric of 200
B. All networks except 10.0.0.0/8 will be allowed and assigned a metric of 200
C. The network 172.16.0.0/16 will be allowed and assigned a metric of 200
D. The network 192.168.1.0 will be allowed and assigned a metric of 100
Refer to the exhibit. R1 and R2 have been configured to share routing information via EIGRP. What will be the result of the configuration section shown for R2? （）
A. Any routes learned by R2 from the interface tied to the 172.16.0.0 network will not be advertised to neighbors on the 192.168.2.0 network.
B. Only routes learned by R2 from the interface tied to the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.
C. Only the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.
D. All networks, except the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network .
The following exhibit shows ipv6 route output. What would the metric be fo r a summary route that summarizes all three OSPFv3 routes displayed?（）
A. 160
B. 140
C. 120
D. 100
最新試題
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
Which of the following are true of both OSPFv2 and OSPFv3?（）
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Which of the following answers lists a multicast IPv6 address?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?（）