Refer to the exhibit. The routing protocols EIGRP and OSPF have been configured as indicated in the exhibit. Given the partial configuration of router R2, which network will be present in th e routing table of R4?（）
A. Network B
B. Network A and Network B
C. Network A
D. neither Network A nor Network B
您可能感興趣的試卷
你可能感興趣的試題
A. L1 ES
B. L2 IS
C. L2 ES
D. L1 IS
E. L1/L2 IS
A. IS - IS is more CPU - intensive than is OSPF
B. For greater fine tuning there are more IS - IS timers
C. IS - IS LSP con tains TLV fields and OSPF LSU contains the LSAs
D. New additions to the protocol are easily implemented in OSPF but not with IS - IS
E. OSPF has more area types than does IS - IS
A. uses a default IOS metric of 10 on each interface
B. uses an on - demand circuit to reduce the hello and LSA flooding across switched WAN li nks,such as ISDN
C. uses a DIS and a backup DIS to present the psuedo - node on the LAN
D. encapsulates PDUs directly into a data - link frame
E. uses stubby areas to improve network scalability
F. runs PRC (Partial Route Calculations) to calculate IP re achability information
A. BGP requires redundant TCP sessions between iBGP peers.
B. Routes learned via eBGP are never propagated to other iBGP peers.
C. A full mesh allows for optimal routing within the Transit AS.
D. Routes learned via iBGP are never propagated to other eBGP peers.
E. Routes learned via iBGP are never propagated t o other iBGP peers.
Given the network diagram, which address would successfully summarize only the networks seen? （）
A. 192.168.0.0/24
B . 192.168.8.0/20
C. 192.168.8.0/21
D. 192.168.12.0/20
E. 192.168.16.0/21
F. These networks cannot be summarized.
最新試題
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best