Which of the following LSA types describes topology information that, when changed, requires a router in the same area to perform an SPF calculation?（）
A. 1
B. 2
C. 3
D. 4
E. 5
F. 7
您可能感興趣的試卷
你可能感興趣的試題
R1 is internal to area 1, and R2 is internal to area 2. Subnet 10.1.1.0/24 exists in area 2 as a connected subnet off R2. ABR ABR1 connects area 1 to backbone area 0, and ABR2 c onnects area 0 to area 2.
Which of the following LSAs must R1 use when calculating R1's best route for 10.1.1.0/24?（）
A. R2's Type 1 LSA
B. Subnet 10.1.1.0/24's Type 2 LSA
C. ABR1's Type 1 LSA in area 0
D. Subnet 10.1.1.0/24's Type 3 LSA in Area 0
E. Subnet 10.1.1.0/24's Type 3 LSA in Area 1
Routers R1, R2, R3, and R4 connect to the same 10.10.10.0/24 LAN- based subnet. OSPF is fully working in the subnet. Later, R5, whose OSPF priority is higher than the other four routers, joins the subnet.
Which of the following are true about the OSPF database exchange process over this subnet at this point?（）
A. R5 will send its DD, LSR, and LSU packets to the 224.0.0.5 all - DR - routers multicast address.
B. R5 will send its DD, LSR, and LSU pack ets to the 224.0.0.6 all - DR - routers multicast address.
C. The DR will inform R5 about LSAs by sending its DD, LSR, and LSU packets to the 224.0.0.6 all- SPF - routers multicast address.
D. The DR will inform R5 about LSAs by sending its DD, LSR, and LSU pa ckets to the 224.0.0.5 all- SPF - routers multicast address.
A. LSR
B. LSAck
C. LSU
D. DD
E. Hello
A verification plan shows a network diagram with branch office Routers B1 through B100, plus two ABRs, ABR1, and ABR2, all in area 100. The branches connect to the ABRs using Frame Relay point - to - point subinterfaces. The verification plan lists the output of the show i p ospf database summary 10.100.0.0 command on a router B1, one of the branches.
Which of the following is true regarding the output that could be listed for this command?（）
A. The output lists nothing unless 10.100.0.0 has been configured as a summary rou te using the area range command.
B. If 10.100.0.0 is a subnet in area 0, the output lists one Type 3 LSA, specifically the LSA with the lower metric when comparing ABR1's and ABR2's LSA for 10.100.0.0.
C. If 10.100.0.0 is a subnet in area 0, the output lists two Type 3 LSAs, one each created by BR1 and ABR2.
D. None, because the Type 3 LSAs would exist only in the ABR's LSDBs.
A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG.
For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）
A. When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.
B. When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.
C. When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.
D. When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.
E. None of the other answers is correct.
最新試題
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?（）