A. CIS 1# show class-map forward Class map match-all forward ( id 3) Match ip dscp 18
B. CIS1#show access-map block Class map match-all block (id 4) Match ip dscp 43
C. CIS1# show class-map real-time Class map match-all block (id 5) Match ip dscp 16
D. CIS 1# show class-map pass Class map match-all real-time (id 2) Match ip dscp 40
您可能感興趣的試卷
你可能感興趣的試題
You are an experienced network administrator in an international company. During your working hours, customers complain that they experience intermittent data loss and they intermittently fail to connect to crucial servers. As shown in the following topology, the 802.1Q trunk between DSW111 and ASW1 fails. Though DSW112 is in the service of HSRP group 11, the SVI for VLAN 11 is up on DSW111.
So as to figure out the problem,
which three commands should you issue on DSW111? （）(Choose three.)
A. show standby vlan 11 brief
B. show interfaces vlan 11
C. show spanning-tree vlan 11
D. show interfaces
You are troubleshooting an issue which is causing full-sized packets entering the MPLS cloud be dropped. You have discovered that one of the switches in the MPLS core is not a Cisco switch, but otherwise the MPLS MTU size is set to 1508 bytes on the routers.
Based on this information, which of these may be the reason the packets are being dropped?（）
A. The switch on you MPLS core that was not produced by Cisco does not support oversized packets
B. No switches support oversized packets
C. By definition, the maximum MTU is 1500 bytes
D. As MPLS VPN labeling increases the size of the packet by 8 bytes, the IP MTU should have been changed to 1508
A. Layer 2 TTL
B. Layer 3 TTL
C. Layer 3 source address
D. Layer 3 destination address
A. Show module
B. Show errdisable detect
C. Show environment
D. Show diagnostic content
A Catalyst switch has just been installed and configured, and is not working as expected. You have decided to capture multiple show command outputs to study.
Which one command could you use that includes the output of many other show commands, such as show version and show running-config?（）
A. show configuration
B. show memory
C. show stacks
D. show tech-support
最新試題
Which command is used to view IPv6 parameters related to the BGP process?（）
Which three of these items are IPv6 transition mechanisms? （）(Choose three.)
Which keyword is used with the debug ipv6 [keyword] command to troubleshoot neighbor discovery problems?（）
What is the maximum number of Cisco Catalyst 3750 Series Switches that can be united into a single manageable unit using the Cisco StackWise technology?（）
Refer to the exhibit. Analyze the two traceroutes that are displayed. Which of these statements is correct in describing what most likely caused the traceroute differences?（）
Refer to the exhibit. For the given configuration, on packets leaving the router on interface FastEthernet0/0 that matches the high traffic class, what will the MPLS experimental bit be set to?（）
Refer to the exhibit. You have a non-Cisco switch that is not communicating properly while connected to the distribution-layer Cisco switching fabric.Which two best-practice actions can you take to overcome this problem? （）(Choose two.)
Which of the following is an easy-to-use tool that allows you to easily configure and monitor Cisco Integrated Services Routers?（）
Refer to the exhibit. You want to minimize the downtime that results from supervisor engine switchovers on Cisco 6500 Series Switches and Cisco 7600 Series Routers. To achieve this, you are considering deploying a Cisco Nonstop Forwarding with Stateful Switchover solution using OSPF.In the exhibit you can see the output of the show ip ospf neighbor detail command.Which trait of systems using Cisco Nonstop Forwarding with Stateful Switchover and OSPF is shown in the exhibit output and will impact your plan?（）
Refer to the exhibit. Which SSH sessions will the SSH server accept?（）