On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter,the status LED and activity LED arealternating on and off.
What does this indicate？（）
A.The client card is not associated to the network.
B.The client card has awakened from power-save mode.
C.The driver has been installed incorrectly.
D.The client card has failed.
您可能感興趣的試卷
你可能感興趣的試題
You have very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved forthe Cisco 7920 phones.
What is the lowest percentage of voice-allocated bandwidth you can select ontheWLAN controller？（）
A.55 percent
B.75 percent
C.40 percent
D.25 percent
Your customer has deployed a Cisco Wireless Location Appliance within its warehouseenvironment.
However， employees there have been experiencing problems when tracking objects using activeRFID tags.
You use an access point scan to determine if the Location Appliance has been deployed correctly.
Making which change to warehouse deployment location services will most likely correct theproblem？（）
A.ensure channels are deployed such that they do not overlap
B.allow for the automatic containment of rogue access points
C.ensure each area is covered by a minimum of three access points
D.ensure a minimum RSSI value of -50
A.4
B.32
C.8
D.16
A Cisco 4404 WLAN controller is being connected to a Cisco 6500 Catalyst Series Switch.
How would you interconnect and configure LAG for connectivity and ensure redundancy？（）
A.All four ports from the Cisco WLC terminated to the same Catalyst gigabit module and channelgroup.
B.Ports 1 and 2 from Cisco WLC to Catalyst gigabit module slot 1 channel group 10 and CiscoWLC ports3 and 4 to Catalyst gigabit module slot 2 channel group 10.
C.All four ports from the Cisco WLC terminated to the same Catalyst gigabit module using two channel groups.
D.Ports 1 and 2 from Cisco WLC to Catalyst gigabit module slot 1 channel group 20 and CiscoWLC ports 3 and 4 to Catalyst gigabit module slot 2 channel group 40.
A.50 feet [15 meters]
B.200 feet [60 meters]
C.150 feet [45 meters]
D.100 feet [30 meters]
最新試題
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）