A.Mirror
B.Rogue Detector
C.Sniffer
D.Monitor
您可能感興趣的試卷
你可能感興趣的試題
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAPAP2.
H-REAP AP2 has six other clients associated to it，which continue to pass traffic.
What hascaused thisproblem？（）
A.H-REAP AP1 has reached its client limit.
B.H-REAP AP2 has reached its client limit.
C.H-REAP AP2 lost its connection to the controller.
D.H-REAP AP1 lost its connection to the controller.
You are trying to change the polling parameters used by the location manager via the Cisco WCS，andyour request is being denied.
What is wrong？（）
A.Polling values can be changed only in the maintenance window.
B.Polling values can be changed only on the location server.
C.Your login does not have the correct permissions.
D.You must wait for the location server to become available.
A.System Monitoring
B.Security Administration
C.Operations Setup
D.Problem Management
On a Cisco 1000 Series controller-based access point， the alarm LED is flashing red， but the otherLEDs are off.
What is this access point indicating？（）
A.Its IP address already exists.
B.It is operating normally.
C.It requires a code upgrade.
D.It has lost contact with the controller.
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network，but clients using PEAP are failing to log on.
Which situation would result in thistype ofproblem？（）
A.Posture validation has not been enabled.
B.The AAA server is set to accept both MS-CHAP v2 and GTC for PEAP authentication.
C.Clients and server are not using certificates.
D.Clients have been set to validate the server identity.
最新試題
On a WLAN controller， what is the default roaming bandwidth percentage reserved for voice clients？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）