Your customer has deployed a Cisco Wireless Location Appliance within its warehouse environment. However，employees there have been experiencing problems when tracking objects using active RFIDtags. The RFID beacon rate is 10 seconds and you have discovered an issue with the RFID timeout value.
Where and how should the RFID value be changed？（）
A.on the Cisco WCS， to 95 seconds
B.on the Cisco WCS， to 45 seconds
C.on the wireless controller， to 95 seconds
D.on the wireless controller， to 45 seconds
您可能感興趣的試卷
你可能感興趣的試題
Your customer has deployed a Cisco Wireless Location Appliance within its warehouse environment. However，employees there have been experiencing problems when tracking objects using active RFIDtags. The RFID tag data is not being collected.
On which device would you verify that RFIDs have beenenabled？（）
A.Cisco WCS
B.access point
C.location manager
D.wireless controller
You are trying to change the polling parameters used by the location manager via the Cisco WCS， and yourrequest is being denied.
What is wrong？（）
A.Your login does not have the correct permissions.
B.You must wait for the location server to become available.
C.Polling values can be changed only on the location server.
D.Polling values can be changed only in the maintenance window.
During the installation of the Cisco WCS version 4.0， an error occurs.
Where would you look for theinstallation log， in order to learn more about this error？（）
A.in the Cisco WCS installation directory
B.at the root of the installation drive
C.in the Cisco WCS\Logs directory
D.on the desktop of the server
A.Multiple controller-based access points will load-balance the containment task using fewer resources than a single access point.
B.Clients connected to the rogue access point may be out of the range of the controller-based access point providing containment.
C.Each controller-based access point can handle only a limited amount of clients connected to the rogue access points.
D.Clients connected to the rogue access point must be able to connect to the containment controller-based access point.
A.three
B.four
C.five
D.six
最新試題
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode？（）
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）