On a Cisco 1000 Series controller-based access point， the alarm LED is flashing red， but the other LEDsare off.
What is this access point indicating？（）
A.It has lost contact with the controller.
B.It requires a code upgrade.
C.It is operating normally.
D.Its IP address already exists.
您可能感興趣的試卷
你可能感興趣的試題
On a standalone access point， client association using EAP-Cisco Wireless （Cisco-LEAP） is failing， butassociation using EAP-PEAP is functioning.
What needs to be enabled on the standalone access point tocorrect this issue？（）
A.a shared key
B.network EAP
C.open authentication plus EAP
D.open authentication plus MAC
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2. H-REAP AP2 has six other clients associated to it， which continue to pass traffic.
What has caused this problem？（）
A.H-REAP AP1 lost its connection to the controller.
B.H-REAP AP2 lost its connection to the controller.
C.H-REAP AP1 has reached its client limit.
D.H-REAP AP2 has reached its client limit.
A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24 PWRSwitch. However， when it is powered up， the access point fails.
What has caused this problem？（）
A.access point has not been initialized with the primary controller
B.switch port is not enabled
C.switch does not support 802.3af
D.access point does not support 802.11h
E.incorrect switch power supply
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installation mode.When you set the link back to operational mode you loose association to the root bridge.
Which action willcorrect the problem？（）
A.Configure the proper channel.
B.Enable passwords on both bridges.
C.Configure the distance parameter value.
D.Configure the bridge to force infrastructure devices to associate only to the SSID parameter.
On a Cisco Aironet 1130AG Series standalone access point，the status LED is dark blue andblinking.
What does this indicate？（）
A.The access point is booting.
B.The internal radio has failed.
C.An access point buffer overflow is occurring.
D.A firmware upgrade is in progress.
最新試題
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）