A.6 percent
B.12 percent
C.18 percent
D.24 percent
您可能感興趣的試卷
你可能感興趣的試題
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones.
Which two general control settings should you select？ （）
A.Aggressive Load Balancing on
B.Aggressive Load Balancing off
C.Multicast on
D.Multicast off
E.AP Fallback on
F.AP Fallback off
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to the wirelessnetwork， but clients using PEAP are failing to log on.
Which situation would result in this type of problem？（）
A.The AAA server is set to accept both MS-CHAP v2 and GTC for PEAP authentication.
B.Clients have been set to validate the server identity.
C.Posture validation has not been enabled.
D.Clients and server are not using certificates.
You review the Failed Attempts logs on an AAA server and find： "unknown network access server error."
Which failure could produce this error？（）
A.failure of the wireless client and AAA server handshake
B.supplicant authentication failureB.AAA client and AAA server handshake failure
C.wrong password used by the supplicant
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter， the status LED and activity LED arealternating on and off.
What does this indicate？（）
A.The client card has failed.
B.The client card is not associated to the network.
C.The driver has been installed incorrectly.
D.The client card has awakened from power-save mode.
A.4 to 6 times the tag beaconing rate
B.6 to 8 times the tag beaconing rate
C.8 to 10 times the tag beaconing rate
D.10 to 12 times the tab beaconing rate
最新試題
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network， but clients using PEAP are failing to log on.Which situation would result in thistype of problem？（）
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）