A. The OTV control-plane protocol uses the IS-IS protocol to establish adjacencies and exchange MAC reachability across the overlay network. You must enable IS-IS with the feature isis command before OTV adjacencies can be established.
B. OTV uses an SSM group range for neighbor discovery and to exchange MAC reachability with other OTV edge peers.
C. The OTV join interface is a routed uplink interface on the edge device used to physically join the overlay network.
D. The OTV internal interface encapsulates the site Layer 2 frames in IP unicast or multicast packets that are then sent to the other sites.
您可能感興趣的試卷
你可能感興趣的試題
A. C84C·75FA·6000
B. 01005·E11.·2FD
C. C84C·76FA·6000
D. 4000.0000.0001
A.The following XML-based NETCONF operations are supported in NX-OS SoftwarE˙close-session copy-config delete-config and edit-config
B.The following XML-based NETCONF operations are supported in NX-OS SoftwarE˙close-session copy-config edit-config and kill-session
C.NX-OS Software supports up to a maximum of 16 concurrent XML sessions
D.Only show commands are supported via the XML management interface in NX-OS Software
E.The NX-OS implementation of the XML-based NETCONF requires SSH to be used for communication with the device
A. In a vPC topology， the primary HSRP router will respond to ARP requests， but both HSRP routers will forward data traffic. No additional configuration is required.
B. In a vPC topology， the primary HSRP router will respond to ARP requests， but both HSRP routers will forward data traffic if the peer-gateway feature is enabled.
C. You can configure two overlapping HSRP groups to load share traffic from the connected hosts while providing the default router redundancy.
D. You can use the show standby command to verify HSRP operation and configuration.
E. If you remove the feature hsrp command， all relevant HSRP configuration information isalso removed.
A. Switch profiles allow configurations to be synchronized between switches and are supported with any Cisco NX-OS Software managed device.
B. DCNM LAN can archive configurations from devices even if they are not managed by the DCNM server， and the administrator can supply the device management IP address and credentials.
C. You can archive a maximum of 50 configuration versions per managed device.
D. Managed devices must be licensed in DCNM LAN before they can be used with configuration change management.
E. Device-running configuration will be archived only if it differs from the last archived version.
Nexus# conf t
Enter configuration commands， one per line. End with CNTL/Z.
Nexus（config）# interface Loopback10
% Permission denied Nexus（config）# ？
no Negate a command or set its defaults
username Configure user information.
end Go to exec mode
exit Exit from command interpreter
What is the reason why this user is not able to enter configuration commands？（）
A. The user did not enter enable prior to going into configuration mode.
B. The software license installed on Nexus is Layer 2 only， which does not allow the creation of Layer 3 interfaces.
C. The user RBAC role is set to network-operator.
D. The user failed authentication and user access defaulted to read-only mode.
E. The AAA server is currently not responding.
最新試題
Which are valid statements about Cisco Virtual Interface Card （VIC）？ （）
What is required for Cisco UCS C-Series rack server integration with Cisco UCS Manager？（）
Which statements are true regarding the Cisco UCS fabric failover feature？ （）
In a Cisco Unified Computing System， What is the "designated receiver" port in end-host mode used for？（）
When testing ICMP access to a functional load-balancing ACE VIP， it fails. What is the reason of this problem？ （）
Which is true when describing a connection replication in Cisco ACE？（）
A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types？（）
What is the purpose of this command in a Cisco Application Control Engine？（） switch/Admin# show np 1 me-stats "-F0 v"
What is the use of an "all configuration" backup in Cisco UCS？（）
In a Cisco Unified Computing System， where are SAN port channels connected to？（）