A. Synchronizes ARP entries between vPC peers every five minutes
B. Triggers a manual update of ARP entries from the primary peer to the secondary
C. Enables a bulk loading of ARP entries when a vPC peer is restored
D. Uses the peer-keepalive link to maintain ARP table consistency
您可能感興趣的試卷
你可能感興趣的試題
A. admin， operator， network-admin， and network-operator
B. admin， read-only， network-admin， and network-operator
C. vdc-admin， vdc-operator， network-admin， and network-operator
D. vdc-admin， vdc-operator， network-admin， and network-operator （for Nexus 7000） and network- admin and network-operator （for other Nexus switches）
E. admin and read-only
A. IGMP is not synchronized between vPC peers
B. Cisco Fabric Service carries IGMP entries across the vPC peer link
C. IP ARP synchronization under the vPC domain configuration also synchronizes IGMP
D. IGMP is flooded to the L2 domain， and there is no need to synchronize it between vPC peers
A. The OTV control-plane protocol uses the IS-IS protocol to establish adjacencies and exchange MAC reachability across the overlay network. You must enable IS-IS with the feature isis command before OTV adjacencies can be established.
B. OTV uses an SSM group range for neighbor discovery and to exchange MAC reachability with other OTV edge peers.
C. The OTV join interface is a routed uplink interface on the edge device used to physically join the overlay network.
D. The OTV internal interface encapsulates the site Layer 2 frames in IP unicast or multicast packets that are then sent to the other sites.
A. C84C·75FA·6000
B. 01005·E11.·2FD
C. C84C·76FA·6000
D. 4000.0000.0001
A.The following XML-based NETCONF operations are supported in NX-OS SoftwarE˙close-session copy-config delete-config and edit-config
B.The following XML-based NETCONF operations are supported in NX-OS SoftwarE˙close-session copy-config edit-config and kill-session
C.NX-OS Software supports up to a maximum of 16 concurrent XML sessions
D.Only show commands are supported via the XML management interface in NX-OS Software
E.The NX-OS implementation of the XML-based NETCONF requires SSH to be used for communication with the device
最新試題
KAL-AP on the Cisco ACE allows communication with Cisco ACE Global Site Selector， to report virtual IP and real server availability. Which statement is true about KAL-AP？（）
From the Cisco UCS CLI， how do you verify which uplink ports a blade server is using for its network connectivity？（）
An administrator creates a vNIC and assigns it to Fabric A with the fabric failover feature enabled. Which statement is true？（）
Where are SAN Port Channel is created in UCS Manager？（）
Given a Cisco Unified Computing System， which is a valid port type in end-host mode？（）
Given the following output： san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24：0c：00：0d：ec：d3：5c：00 Admin port mode is NP， trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] ： fc2/3 Member[2] ： fc2/4 What does "Speed is 8 Gbps" indicate？（）
Which statement is true regarding Backup tasks in Cisco UCS？（）
In the event of a GSS failure in a GSS cluster， which is true？（）
Server load balancing （SLB） is the process of deciding to which server a load-balancing device should send a client request for service. Which predictors are supported on ACE in order to select the best server to fulfill a client request？ （）
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）