A.An SVI is normally created for the default VLAN (VLAN1) to permit remote switchadministration
B.Multiple SVIs can be associated with a VLAN
C.SVI is another name for a routed port
D.An SVI is created by entering the no switchport command in interface configuration mode
E.An SVI provides a default gateway for a VLAN
您可能感興趣的試卷
你可能感興趣的試題
A.private VLANs
B.port security
C.BPDU guard
D.dynamic ARP inspection
E.DHCP snooping
A.Router ACLs can be applied to the input and output directions of a VLAN interface
B.Bridged ACLs can be applied to the input and output directions of a VLAN interface
C.Only router ACLs can be applied to a VLAN interface
D.VLAN maps and router ACLs can be used in combination
E.VLAN maps can be applied to a VLAN interfac
A.Trunk
B.Isolated
C.Primary
D.Community
E.Promiscuous
F.None of the other alternatives apply
Refer to the exhibit. The user who is connected to interface FastEthernet 0/1 is on VLAN 10 andcannot access network resources. On the basis of the information in the exhibit, which commandsequence would correct the problem?()
A.SW1(config)# interface fastethernet 0/1 SW1(config-if)# no shut
B.SW1(config)# interface fastethernet 0/1 SW1(config-if)# switchport mode access SW1(config-if)# switchport access vlan 10
C.SW1(config)# vlan 10 SW1(config-vlan)# state active
D.SW1(config)# interface fastethernet 0/1 SW1(config-if)# switchport mode access
E.SW1(config)# vlan 10 SW1(config-vlan)# no shut
You work as a network Technician. A new workstation has consistently been unable to obtain anIP address from the DHCP server when the workstation boots. Older workstations function
normally, and the new workstation obtains an address when manually forced to renew its address.
What should be configured on the switch to allow the workstation to obtain an IP address at boot?()
A.UplinkFast on the switch port connected to the server
B.BackboneFast on the switch port connected to the server
C.PortFast on the switch port connected to the workstation
D.trunking on the switch
最新試題
As a network engineer, do you know for what purpose SDM uses Security Device Event Exchange(SDEE)?()
Drag and drop each management protocol on the above to the correct category on the below.
As a network technician, do you know what is a recommended practice for secure configurationmanagement?()
A new router was configured with the following commands:The configuration above was found on an Internet Service Provider’s (ISP) Multiprotocol LabelSwitching (MPLS) network. What is its purpose?()
Authentication is the process of determining if a user or identity is who they claim to be. Refer tothe exhibit. Which statement about the authentication process is correct?()
Drag the IPsec protocol description from the above to the correct protocol type on the below.(Notall descriptions will be used)Drag and Drop question, drag each item to its proper location.
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions, you will need to referto the SDM and the topology, neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete?()
Drag and drop question. The upper gives the MPLS functions, the bottom describes the planes.Drag the above items to the proper location at the below
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec, which two parameters are required when defining the tunnel interfaceinformation?()
Study this exhibit carefully. What information can be derived from the SDM firewall configurationdisplayed?()