Refer to the show spanning-tree mst configuration output shown in the exhibit.
What should be changed in the configuration of the switch SW_2 in order for it to participate in the same MST region？ （）
A. Switch SW_2 must be configured with an instance number of 2.
B. Switch SW_2 must be configured with a different VLAN range.
C. Switch SW_2 must be configured with the revision number of 1.
D. Switch SW_2 must be configured with a different MST name.
您可能感興趣的試卷
你可能感興趣的試題
While logged into a Company switch you issue the following command：
CompanySwitch（config-mst）# instance 10 vlan 11-12
What does this command accomplish？（）
A. It enables a PVST+ instance of 10 for vlan 11 and vlan 12
B. It enables vlan 11 and vlan 12 to be part of the MST region 10
C. It maps vlan 11 and vlan 12 to the MST instance of 10.
D. It creates an Internal Spanning Tree （IST） instance of 10 for vlan 11 and vlan 12
E. It create a Common Spanning Tree （CST） instance of 10 for vlan 11 and vlan 12
F. It starts two instances of MST， one instance for vlan 11 and another instance for vlan 12.
Which MST configuration statement is correct？ （）
A. MST configurations can be propagated to other switches using VTP.
B. After MST is configured on a Switch， PVST+ operations will also be enabled by default.
C. MST configurations must be manually configured on each switch within the MST region.
D. MST configurations only need to be manually configured on the Root Bridge.
E. MST configurations are entered using the VLAN Database mode on Cisco Catalyst switches.
A. MST00
B. MST01
C. the last MST instance configured
D. none
A. Region name
B. Configuration revision number
C. VLAN instance map
D. IST STP BPDU hello timer
E. CST instance map
F. PVST+ instance map
Which of the following specification will allow you to： associate VLAN groups to STP instances so you can provide multiple forwarding paths for data traffic and enable load balancing？ （）
A. IEEE 802.1d （STP）
B. IEEE 802.1s （MST）
C. IEEE 802.1Q （CST）
D. IEEE 802.1w （RSTP）
最新試題
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
What two things will occur when an edge port receives a BPDU？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
What is the configured priority value of the Vlan105’s group on DS2 ？（）