LDAP is being utilized throughout the Company Wireless network.
Which issue or set of issues does the Lightweight Access Point Protocol （LWAPP） address？ （）
A. Reduction of processing in wireless controllers
B. Distributed approach to authentication， encryption， and policy enforcement
C. Access point discovery， information exchange， and configuration
D. Provides security by blocking communication between access points and wireless clients
E. None of the other alternatives apply.
您可能感興趣的試卷
你可能感興趣的試題
Study the exhibit shown below carefully. A Cisco Aironet Wireless LAN Client Adapter has been installed and configured through the ADU on the PC. The Aironet System Tray Utility （ASTU） has been enabled during the installation and the icon appears in the system tray area in the lower right of the desktop as shown：
What is the significance of this icon？ （）
A. It indicates that the client adapter is not associated to an access point or another client.
B. It indicates that the radio of the client adapter is disabled.
C. It indicates that the client adapter is associated to an access point or another client， but the user is not EAP authenticated.
D. It indicates that the client adapter is associated to an access point or another client， that theuser is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is poor.
E. It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is fair.
F. It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is excellent or good.
Which three statements are true about implementing wireless LANs in the Company network using Cisco devices？（）
A. Antenna power is a relative value reference to dBi.
B. LWAPP allows encrypted communications between lightweight access points and WLAN controllers.
C. Characteristics of antennas are directionality， gain， and polarization.
D. Power over Ethernet （PoE） is only available when a WLAN controller is integrated into the network.
E. The WLAN solution Engine （WLSE） is used to control lightweight access points.
F. One of the advantages of the lightweight WLAN solution is that the devices act indepently.
Under which three conditions does a client initiate roaming between wireless cells in the Company WLAN？ （）
A. The access point has broadcast too many SSIDs.
B. The wireless client has missed too many beacons from the access point.
C. The maximum data retry count， initiated by the wireless client， is exceeded.
D. The wireless client has reduced the data rate.
E. The access point has requested client reauthentication.
F. The wireless client has missed too many IAPP （Inter Access Point Protocol） updates.
Refer to the exhibit. The wireless user is moving from right to left towards AP2.
What are three reasons that the wireless client would initiate roaming？（）
A. The minimum data retry count from AP1 is exceeded.
B. The maximum data retry count from AP1 is exceeded.
C. The client has missed too many beacons from AP1.
D. The client data rate from AP1 has been reduced.
E. The client has received too many beacons from AP2.
F. The client data rate from AP2 has been increased.
Refer to the exhibit.
Which protocol establishes an optimal path to the root in a wireless mesh network？ （）
A. Adaptive Wireless Path （AWP）
B. WLAN Quality of Service （WQoS）
C. Lightweight Access Point Protocol （LWAPP）
D. 802.1Q WLAN trunking protocol
E. Layer 2 Roaming （IAPP）
最新試題
Refer to the exhibit. For what purpose is the command show ip cef used？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Which two statements about the various implementations of STP are true？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
What two things will occur when an edge port receives a BPDU？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）