You need to configure a new Company Catalyst 3560 switch for a VOIP-enabled office.
Which three statements are true about the voice VLAN feature on this switch？（）
A.The default CoS value for incoming traffic is set up to 0.
B.The CoS value is trusted for 802.1p or 802.1q tagged traffic.
C.PortFast is automatically disabled when a voice VLAN is configured.
D.The voice VLAN feature is disabled by default.
E.The IP phone accepts the priority of all tagged and untagged traffic and sets the CoS value to 4.
F.When the voice VLAN feature is enabled， all untagged traffic is sent according to the default CoS priority of the port
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Which statement is true about a voice VLAN？（）
A.Physically the voice network and the data network are separate.
B.The voice traffic will normally be on a different IP subnet than will the data traffic.
C.End user intervention is necessary to place the phone into the proper VLAN.
D.The same security policy should be implemented for both voice and data traffic.
E.The data VLAN must be configured as the native VLAN.
A.TCP retransmits
B.UDP priority
C.Bursty
D.Delay sensitive
E.Greedy
F.Drop sensitive
Refer to the exhibit.
What are three of the basic components of a VoIP network？（）
A.software voice applications
B.multipoint control unit （MCU）
C.gatekeeper
D.call agent
E.interactive voice response （IVR） systems
F.softphones
A.The use of a queuing method that will give VoIP traffic strict priority over other traffic
B.The use of RTP header compression for the VoIP traffic.
C.The proper classification and marking of the traffic as close to the source as possible
D.The use of 802.1QinQ trunking for VoIP traffic
E.The use of WRED for the VoIP traffic
You need to troubleshoot some problems in the Company VOIP network associated with jitter.
What is the cause of jitter？ （）
A. Packet drops
B. Transmitting too many small packets
C. Variable queue delays
D. Compression
E. None of the other alternatives apply
最新試題
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）