.Refer to the exhibit and the partial configuration on routers R1 and R2. Hot Standby Routing Protocol （HSRP） is configured on the network to provide network redundancy for the IP traffic. The network administrator noticed that R2 does not become active when the R1 serial0 interface goes down.
What should be changed in the configuration to fix the problem？ （）
A. The Serial0 interface on router R2 should be configured with a decrement value of 20.
B. The Serial0 interface on router R1 should be configured with a decrement value of 20.
C. R2 should be configured with a standby priority of 100.
D. R2 should be configured with a HSRP virtual address.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Based on the debug standby output in the exhibit， which HSRP statement is true？ （）
A. DSW111 is the active router because it is the only HRSP-enabled router on that segment.
B. DSW111 is the active router because the standby timer has been incorrectly configured.
C. DSW111 is the active router because it has a lower priority on that VLAN.
D. DSW111 is the active router because it has a lower IP address than the tying priority router on that VLAN.
E. DSW111 is the active router and is advertising the virtual IP address 10.10.10.111 on VLAN 11.
Refer to the exhibit. Based on the debug standby output in the exhibit，
which HSRP statement is true？（）
A. DSW111 is the active router because it is the only HRSP-enabled router on that segment.
B. DSW111 is the active router because the standby timer has been incorrectly configured.
C. DSW111 is the active router because it has a lower priority on that VLAN.
D. DSW111 is the active router because it has a lower IP address than the tying priority router on that VLAN.
E. DSW111 is the active router and is advertising the virtual IP address 10.10.10.111 on VLAN 11.
Refer to the exhibit. Assume that Host A can ping the corporate headquarters and that HSRP is configured on DSw1， which is then reloaded. Assume that DSw2 is then configured and reloaded. On the basis of this information，
what conclusion can be drawn？ （）
A. DSw1 will be the active router because it has the lower priority configured.
B. DSw1 will be the standby router because it has the lower IP address.
C. DSw2 will be the active router because it booted last.
D. DSw1 will be the active router because it booted first.
E. DSw2 will be the active router because it has the higher priority that is configured.
F. DSw2 will be the standby router because it has the higher IP address.
A. Spanning Tree Protocol （STP）
B. Delay reduction
C. Hot Standby Routing Protocol （HSRP）
D. Dynamic routing protocols
E. Quality of Service （QoS）
F. Jitter management
What can be determined about the HSRP relationship from the displayed debug output？ （）
A. Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router 172.16.11.111.
B. Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router 172.16.11.112.
C. The IP address 172.16.11.111 is the virtual HSRP router IP address.
D. The IP address 172.16.11.112 is the virtual HSRP router IP address.
E. The nonpreempt feature is enabled on the 172.16.11.112 router.
F. The preempt feature is not enabled on the 172.16.11.111 router.
最新試題
Refer to the exhibit. Which statement is true about the output？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Which statement is correct about RSTP port roles？（）
Which three statements about STP timers are true？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
What two things will occur when an edge port receives a BPDU？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）