A.Reload the active VLAN configuration
B.Clear the affected port and bring it up again
C.Explicitly set the trunk for the VLAN to be on
D.Remove all the VLANs set
您可能感興趣的試卷
你可能感興趣的試題
A.The link is using IEEE 802.1Q protocol
B.The link is using IEEE 802.1E protocol
C.Spanning tree is disabled
D.Not enough information to determine
E.The native VLAN information is identical at each end of the link
F.The native VLAN information is different at each end of the link
A.IEEE 802.1Q
B.IEEE 802.10
C.Misconfigured NIC
D.User configuration
E.All of the above
A.SW13 has a higher VTP configuration revision than the current VTP revision
B.SW13 is configured as a VTP server with a different domain name
C.SW13 is configured as a VTP server with the domain name R1
D.SW13 has a lower VTP configuration revision than the current VTP revision
E.SW13 is not configured to participate in VTP
F.SW13 is configured with only VLAN1
On the basis of the following exhibit, can you tell me why VLAN updates from switch CK-P2S1 arenot applied to switch CK-P1S1?()
A.The MD5 digests do not match
B.Switch CK-P1S1 is in transparent mode
C.The passwords do not match
D.The VTP domains are different
A.In a 6to4 tunnel, the first two bytes of the IPv6 address will be 0x2002 and the next four byteswill be the hexadecimal equivalent of the IPv4 address
B.In a 6to4 tunnel, the IPv4 address 192.168.99.1 would be converted to the2002:1315:4463:1::/64 IPv6 address
C.In a 6to4 tunnel, the IPv4 address 192.168.99.1 would be converted to the 2002:c0a8:6301::/48IPv6 address
D.In a 6to4 tunnel, the first two bytes of the IPv6 address will be locally derived and the next twobytes will be the hexadecimal equivalent of the IPv4 address
E.In a 6to4 tunnel, the IPv4 address 192.168.99.1 would be converted to the 2002:c0a8:6301::/16IPv6 address
最新試題
Router NetworkTut is configured as shown below:Given the above configuration, which statement is true?()
Drag and drop each management protocol on the above to the correct category on the below.
In computer security, AAA stands for authentication, authorization and accounting. Which optionabout the AAA authentication enable default group radius enable command is correct?()
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions, you will need to referto the SDM and the topology, neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define?()
Drag and drop the xDSL type on the above to the appropriate xDSL description on the below.
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec, which two parameters are required when defining the tunnel interfaceinformation?()
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
Which three statements accurately describe IOS Firewall configurations?()
Refer to the exhibit. Which two statements about the AAA configuration are true?()
A new router was configured with the following commands:The configuration above was found on an Internet Service Provider’s (ISP) Multiprotocol LabelSwitching (MPLS) network. What is its purpose?()