A.Static IP routes are maintained across a switchover because they are configured from entries inthe configuration file
B.Information about dynamic routing states， maintained on the active supervisor engine， issynchronized to the redundant supervisor engine and is transferred during the switchover
C.Information about dynamic routing states， maintained on the active supervisor engine， is notsynchronized to the redundant supervisor engine and is lost on switchover
D.The Forwarding Information Base （FIB） tables are cleared on a switchover. As a result， routedtraffic is interrupted until route tables reconverge
E.Static IP routes are cleared across a switchover and recreated from entries in the configurationfile on the redundant supervisor engine
F.The Forwarding Information Base （FIB） tables are maintained during the switchover. As aresult， routed traffic continues without any interruption when the failover occurs
您可能感興趣的試卷
你可能感興趣的試題
A.An SVI is normally created for the default VLAN （VLAN1） to permit remote switchadministration
B.Multiple SVIs can be associated with a VLAN
C.SVI is another name for a routed port
D.An SVI is created by entering the no switchport command in interface configuration mode
E.An SVI provides a default gateway for a VLAN
A.private VLANs
B.port security
C.BPDU guard
D.dynamic ARP inspection
E.DHCP snooping
A.Router ACLs can be applied to the input and output directions of a VLAN interface
B.Bridged ACLs can be applied to the input and output directions of a VLAN interface
C.Only router ACLs can be applied to a VLAN interface
D.VLAN maps and router ACLs can be used in combination
E.VLAN maps can be applied to a VLAN interfac
A.Trunk
B.Isolated
C.Primary
D.Community
E.Promiscuous
F.None of the other alternatives apply
Refer to the exhibit. The user who is connected to interface FastEthernet 0/1 is on VLAN 10 andcannot access network resources. On the basis of the information in the exhibit， which commandsequence would correct the problem？（）
A.SW1（config）# interface fastethernet 0/1 SW1（config-if）# no shut
B.SW1（config）# interface fastethernet 0/1 SW1（config-if）# switchport mode access SW1（config-if）# switchport access vlan 10
C.SW1（config）# vlan 10 SW1（config-vlan）# state active
D.SW1（config）# interface fastethernet 0/1 SW1（config-if）# switchport mode access
E.SW1（config）# vlan 10 SW1（config-vlan）# no shut
最新試題
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
Drag the DSL technologies on the left to their maximum（down/up） data rate values on the below.
In computer security， AAA stands for authentication， authorization and accounting. Which optionabout the AAA authentication enable default group radius enable command is correct？（）
Which statement correctly describes IPsec VPN backup technology？（）
Drag each element of the Cisco IOS Firewall Feature Set from the above and drop onto itsdescription on the below.
Drag the correct statements about MPLS-based VPN on the left to the boxes on the right.（Not allstatements will be used）
As a network engineer， do you know for what purpose SDM uses Security Device Event Exchange（SDEE）？（）
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
Drag and drop each function on the above to the hybrid fiber-coaxial architecture component that itdescribes on the below.
Drag the DSL local loop topic on the left to the correct descriptions on the right.