Refer to the exhibit. On the basis of the configuration that is provided, how would the BGP updates that come from router R1 be replicated inside autonomous system 65200？（）
A. All BGP updates that are received on router R 2 will be sent to routers R3 and R4. Routers R3 and R4 will then forward those BGP updates to router R5
B. None of the BGP updates that are received on router R2 will ever be received by router R5
C. All BGP updates that are received on router R2 will not be sent to routers R3 and R4
D. All BGP updates that are received on router R2 will be sent directly to router R5
您可能感興趣的試卷
你可能感興趣的試題
A. 228.10.10.7
B. 229.11.10.7
C. 229.138.10.7
D. 229.138.10.8
E. 228.10.10.8
F. 228.10.138.7
A router has two paths to reach another network in a different autonomous system. Neither route was generated by the local router and both routes have the same default weight an d local preference values.
Which statement is true about how BGP would select the best path?（）
A. To influence one route to be preferred, its default local preference value will be changed via the use of the command bgp default local - preference 50
B. Th e router will prefer the shortest autonomous system path
C. If the command bgp always - compare - med has been given, then the router will prefer the route with the highest MED
D. The router will prefer the route with the lower MED
Refer to the exhibit. Which two statement s are correct?（）
A. All the routes were redistributed into BGP from an IGP
B. All the routes were originated by BGP with the network command
C. All six routes will be installed in the routing table
D. Four routes will be installed in the routing ta ble
E. Two routes will be installed in the routing table
Refer to the exhibit. Which two statements are true about the partial configuration that is provided.（）
A. The peer group shortens the EBGP configuration
B. The peer group shortens the IBGP configuration
C. All the configured neighbors are in autonomous system 100
D. Three AS - path filters are applied to each BGP neighbor
E. Only the outgoing filters are applied to BGP updates
A. A virtual link to area 0.
B. OSPF summarization command.
C. default - cost extension to the area command.
D. no - summary extension to the area stub comm and.
E. None of the other alternatives apply
最新試題
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?（）
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Which of the following features work the same in both RIP- 2 and RIPng?（）